Cloning Failed, An error occurred while reading the disk

Samsung Data Migration is a software that allows users to clone HDD or SSD to Samsung branded SSD. It is the easiest mode to switch if you lot are changing, just the hard bulldoze. When I was trying to clone my primary partition, I received a message — Cloning Failed, An error occurred while reading the disk. It was surprising because I had cloned it earlier, and this was my 2nd time. And then I was sure that it has zip to practise with the drive. Information technology took me a while to figure out, so hither is how you tin set up this effect, and clone without any trouble.

Cloning Failed error reading disk

A scrap of background before we go-ahead

I accept a Windows x PC, which is now vi-seven years old. The by few month's performances started degrading. So, I decided somewhen moving to SSD and increased RAM as the only solution. I wasn't set to change the complete setup, as it would take been a waste product of what is however working.

And so I got a Samsung 860 EVO 250 GB, plugged into the computer using a SATA wire from the computer at domicile. That's when I cloned it for the commencement time, and it worked but fine. The adjacent day, I got my new SATA wire, and and so I changed it on my office computer. When I rebooted, I started getting Blue Screen of Death. I tried booting into safety mode, and it still gave me BSOD. Since I had the previous installation intact on my sometime HDD, I booted into that, and it worked fine.

I checked for Hd errors, ran the Samsung Sorcerer tool to check for SSD errors, but nothing. The showtime failure occurred after thirty minutes, and the subsequent tries resulted in errors were within ii-3 minutes. Finally, I decided that it is best to clone it over again, and that's where things got weird.

Samsung Data Migration: Cloning Failed, An fault occurred while reading the disk

When I checked for the mistake, most of them were—An error occurred while writing to the TargetDisk.However, for me, it was reading the disk.

Change SATA Port on Motherboard
Run Chkdisk
Check for Bad sectors on HDD

I am going to share first what worked for me, followed by a few general troubleshooting tips which the information migration tool suggested.

i] Change SATA Port on Motherboard

Cloning Failed error reading disk

The motherboard of my computer has four SATA ports. Out of which two are eSATA ports, while the residual two are marked equally SATA. While I assumed something is wrong with my wire, I first chose to change the port. So I connected information technology with the cherry port or eSATA port, which you see in the above image. Next, I rebooted the estimator, launched the Software Data Migration tool, and it worked.

What still mind boggles me that SATA is used for an internal device connector while eSATA is used as an external device connector. I assume that it is a limitation of Samsung Data Migration software, which might need information technology to be on the same type of ports, or it looks just for 1st and 2d drives. The target drive should likely be the secondary internal drive connection.

The summary from Samsung Data Migration tool hints to something similar:

On systems with two (2) drives or more than (e.g. "C:", "D:", and "E:" drives) with the operating arrangement installed on the "C:" drive, merely the get-go two drives volition be cloned. The "System" partition that is created during Windows installation is automatically replicated.

I could be wrong, only changing the port worked, and both HDD and SSD are on the same type of ports. And so it has to mean something.

2] Run Check Disk tool

Cheque Disk is an inbuilt tool from Microsoft which tin can repair deejay issues which windows can resolve. To run Check Disk on your System Bulldoze (C), using the control line, type the following and press Enter key.

chkdsk /f C:

If required, restart your figurer. Chkdsk command can repair bad sectors if they can be repaired.

three] Check for Bad sectors on HDD

Bad Sectors are part of hard drives that cannot be used to store data. If you have a bad sector on your HDD, then the Migration tool will not clone it. Tools like Hard disk drive Validator tin can help you lot notice and confirm. Download the software from the website, and confirm. There are many third-party tools slike Windows Surface Scanner, HD Melody, Macrorit Disk Scanner, EaseUS Sectionalization Master Gratis, AbelsSoft CheckDrive, HDDScan that delivers a better experience.

I hope the postal service truly helped y'all to fix the problem with the Samsung Data Migration tool, which gives the fault — Cloning Failed, An error occurred while reading the disk . The baseline is to switch the ports and see what works for you. Make sure to ability down the reckoner when you do that. Information technology'due south going to exist tedious, but cloning is the fastest style to switch the hard drive.

Cloning Failed error reading disk